Buy iTroll G2.5 M4 Dual Motor System

iTroll G2.5 Dual Motor System Builder
Systems start at $729.00

iTroll G2.5 STANDARD ITEMS include:
Click Dial (Dual Resolution)
Illuminated Keypad
HUNT Mode Dual
Custom Ball Mount
Options and accessories are additional

IMPORTANT NOTE:
At a minimum, a "Dual motor iTroll system" consists of the "electronics package" in Step 1 combined with TWO motor "fit kits" (one for each motor) in Steps 2 and 3.

Step 1 - Select iTroll G2.5 Electronics Package
ITEMS IN PACKAGE ARE:

1. One iTroll G2.5 Control Head

2. HUNT Mode (software in control head)

3. One "J Hook" Ball (Gimbal) Mount

4. Power Module

5. Dual Motor Software Upgrade

6. One IT.SH.10 second motor wiring harness

Due to the fact that no two iTroll installations are the same, RAM arm(s) and base(s) are NOT included in this package and are available for purchase below.

One electronics package is required per boat.

Example: One boat = Buy ONE electronics package, two boats = Buy TWO electronics packages and so on.

Part# IT.G2.5.DM.Bundle
Qty: @ $469.00 Each

Step 2:
Fit Kits for motors 30HP and lower.

These Fit Kits contain one WATERPROOF servo motor, bracket and linkage to allow it to operate motor's throttle.

Please use APPLICATION GUIDE to verify fit kit BEFORE ordering.

E1.WP Fit Kit Qty: @ $130.00 Each

H.WP Fit Kit Qty: @ $130.00 Each

H1.WP Fit Kit Qty: @ $130.00 Each

H9915.WP Fit Kit Qty: @ $130.00 Each

M1.WP Fit Kit Qty: @ $130.00 Each

M2.WP Fit Kit Qty: @ $130.00 Each

M3.WP Fit Kit Qty: @ $130.00 Each

M4.WP Fit Kit Qty: @ $130.00 Each

M5.WP Fit Kit Qty: @ $130.00 Each

S1.WP Fit Kit Qty: @ $130.00 Each

S1R.WP Fit Kit Qty: @ $130.00 Each

S2R.WP Fit Kit Qty: @ $130.00 Each
(Suzuki 9.9 / 15 / 20 EFI Remote)

S2T.WP Fit Kit Qty: @ $175.00 Each
(Suzuki 9.9 / 15 / 20 EFI Tiller)

T1.WP Fit Kit Qty: @ $130.00 Each

Y.WP Fit Kit Qty: @ $130.00 Each

Y1.WP Fit Kit Qty: @ $130.00 Each

Y2R.WP Fit Kit Qty: @ $130.00 Each

Y3.WP Fit Kit Qty: @ $130.00 Each

Y20.25.R.WP Fit Kit Qty: @ $130.00 Each

Step 3:
Fit Kits for motors LARGER than 30HP.
Note: These fit kits CONTAIN Neutral Safety Interface to protect motor's gear box.

These Fit Kits contain one WATERPROOF servo motor, bracket, linkage and Neutral Safety Interface to allow it to operate motor's throttle.

Please use APPLICATION GUIDE to verify fit kit BEFORE ordering.

Mercury 40 / 50 / 60 HP
Remote control "T" Handle & Big Tiller Models ONLY
Serial # 1C050252 and Up

M456.WP Fit Kit Qty: @ $202.00 Each

Mercury 75 / 90 / 115 HP
Remote control "T" Handle Models ONLY
Serial # 2B095049 and Up

M7.9.11.WP Fit Kit Qty: @191.00 Each

Step 4 - Purchase OPTIONAL Accessory:
RAM Mount 1 Inch Ball Diamond Base

Base plate footprint = 2.43 x 1.31 inches
Hole size (diameter) = 0.22 inches
Spacing between holes (center to center) = 1.912 inches

Note: Our custom mounts have a one inch ball that sticks out of the back of the iTroll control head. A RAM base and arm completes your custom installation!

Part# RAM.Diamond
Qty: @ $9.50 Each

Step 5 - Purchase OPTIONAL Accessory:
RAM Mount 1 Inch Ball Round Base

Base diameter = 2.5 inches

Note: Our custom mounts have a one inch ball that sticks out of the back of the iTroll control head. A RAM base and arm completes your custom installation!

Part# RAM.Round
Qty: @ $10.50 Each

Step 6 - Purchase OPTIONAL Accessory:
RAM Mount Short Arm for 1 Inch Balls

Overall length = 2.42 inches
Spacing between balls (center to center) = 1.75 inches

Note: Our custom mounts have a one inch ball that sticks out of the back of the iTroll control head. A RAM base and arm completes your custom installation!

Part# RAM.Short
Qty: @ $10.50 Each

Step 7 - Purchase OPTIONAL Accessory:
RAM Mount Medium Arm for 1 Inch Balls

Overall length = 3.73 inches
Spacing between balls (center to center) = 3.0 inches

Note: Our custom mounts have a one inch ball that sticks out of the back of the iTroll control head. A RAM base and arm completes your custom installation!

Part# RAM.Medium
Qty: @ $12.50 Each

Step 8 - Purchase OPTIONAL Accessory:
Additional "J Hook" Ball / Gimbal Assembly

Some anglers like to have their iTroll control head in different locations. We sell these due to popular demand!

Part# IT.G3.Ball
Qty: @ $20.00 Each

Step 9 - Purchase OPTIONAL Accessory:
Remote Idle Run Switch

Weather proof touch pads that allow you to "Clone" the Idle / Run button on iTroll's control head so you can place them anywhere in your boat. Only compatible with iTroll G2 and G3 electronics.

You can install multiple switches. It is quite common to have a switch in each rear corner of a boat for maximum convenience!

Part# IT.Remote.Switch
Qty: @ $30.00 Each

Step 10 - Purchase OPTIONAL Accessory:
Neutral Safety Interface

For remote shift & throttle motors ONLY! This interface allows iTroll to read the position of the shifter so it can automatically idle the motor when the shifter is placed in neutral.

Note: If you are purchasing any of the fit kits in Step 3, they include one of these interfaces. DO NOT buy an interface in this step.

Part# IT.NSI
Qty: @ $30.00 Each

Step 11 - Purchase OPTIONAL Accessory:
Cisco Plate to mount RAM Diamond Ball under Cisco electronics mount. Constructed from stainless steel.

Note: This is only the plate, Cisco mount and RAM Diamond ball NOT included.

Part# IT.Cisco
Qty: @ $12.00 Each

Step 12 - Purchase OPTIONAL Accessory:
Spare / Replacement WATERPROOF Servo Motor

We offer these in case you want to keep a spare in your truck or boat.

Note: All iTroll OEM servo motors are manufactured by HiTec and are of top quality. Historically, these have proven to be ultra dependable and we DO NOT have chronic servo failures like the competition. However, many anglers that fish tournaments or take remote trips like to have a spare servo on hand.

Part# IT.WP.Servo
Qty: @ $77.50 Each

Shipping Rates for iTroll complete systems:
"Complete system" = One Electronics Package + One Fit Kit

USA orders: FREE
Canada Orders: $30.00

NOTICE: At the present time, iTroll products can only be ordered online if shipped to USA or Canada.

Please email for international ordering information.

Purchase your iTroll:

iTroll G2.5 & G3: Beyond CompareThe most advanced throttle controllers ever created. Click here to learn more!

iTroll G2.5 Dual Motor System BuilderSystems start at $729.00iTroll G2.5 STANDARD ITEMS include:Click Dial (Dual Resolution)Illuminated KeypadHUNT Mode DualCustom Ball MountOptions and accessories are additional

IMPORTANT NOTE:At a minimum, a "Dual motor iTroll system" consists of the "electronics package" in Step 1 combined with TWO motor "fit kits" (one for each motor) in Steps 2 and 3.

iTroll G2.5 & G3: Beyond Compare
The most advanced throttle controllers ever created. Click here to learn more!

iTroll G2.5 Dual Motor System Builder
Systems start at $729.00

iTroll G2.5 STANDARD ITEMS include:
Click Dial (Dual Resolution)
Illuminated Keypad
HUNT Mode Dual
Custom Ball Mount
Options and accessories are additional

IMPORTANT NOTE:
At a minimum, a "Dual motor iTroll system" consists of the "electronics package" in Step 1 combined with TWO motor "fit kits" (one for each motor) in Steps 2 and 3.